Fort Harrison The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as “Open Cell” because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the “open” space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across a spray foam insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam.
How to Make a Spray Foam TreeIf you are in the process of building a new home or renovating your existing home then finding the ideal insulation is one of the decisions that you will have to make. There are several options available to you. Some products are more affordable in the short term but don't always provide the best long-term insulation solution. Other products may be more expensive to purchase but can save you hundreds of dollars on your utility bills over time. It is useful to compare and understand the different types of insulation so you can make an informed decision that will benefit you in the long run. What Is Spray Foam Insulation? Spray foam is a product that has been around for some time. It is one of the more efficient home insulators and available in a variety of types to suit different applications. It is made up of at least two compounds. Independently, the components can be stored for a relatively long period of time; however, when the compounds are mixed, they react and form foam that needs to be applied immediately. The foam is sprayed on to a surface area and after a short period of time, it sets and hardens. The result is an effective insulating layer that is highly durable. How Does Spray Foam Compare to Other Types of Insulation? Insulation is rated in terms of an R-value. The higher the R-value, the higher the density of the insulator and therefore the higher its effectiveness. It is considered a good insulator because of its comparatively high R-value. Open cell spray foam which has the lowest density has an R-value of 4. Most other types of spray foam have an R-value between 6 and 7.7. Compare this to fiberglass batting which is another common form of insulation that only has an R-value of 3.5. Comparatively speaking, it therefore has an average R-value that is almost double that of fiberglass batting. Another benefit of spray foam is that the application process is much easier. It can be applied to most surfaces regardless of whether they are horizontal or vertical. In all instances the foam can simply be sprayed onto the area that needs to be insulated. There is no measuring and cutting of mats or the need to overlap insulation. It is easy to apply in a uniform manner. It is also generally more durable than other forms of insulation. It does not wear down as easily and therefore protects and insulates your home for a much longer period of time before needing to be replaced. What Makes Spray Foam So Efficient as an Insulator? One of the properties of spray foam is that as it is applied to a surface area, it continues to expand. This means that the foam can get into cracks and crevasses and provide an airtight and watertight seal. It also hardens in a relatively short period of time which means that the application process can be completed in a relatively short space of time. Compared to other types of insulators, its high density is perhaps its most important characteristic. It keeps cold air out and warm air in during the winter months and helps to effectively insulate your home. How Else Does Spray Foam Protect Your Home? Certain types of spray foam have microbial agents as components. These microbial agents help prevent the growth of mold in your home. If you live in a region that has consistently high levels of humidity then your home can be susceptible to mold infestations. Often mold goes unseen and undetected until it is quite severe. This can affect the health of your family. Having an insulator that prevents mold growth can provide a healthier home environment. Spray foam is highly durable. It also can form a protective barrier in your home against vermin and insects. Rather than having to call exterminators, you can pre-empt the problem by insulating your home with this product.
How to Remove Expanding FoamExpanding foam that overexpands and lands where you didn't plan for it -- on hands, clothes, cinderblock or studs -- can pose a removal problem, with the solution depending on the type you use. Polyurethane foams including Dow's Great Stuff, Touch 'n Foam, DAP Kwik Foam and Owens-Corning Insulating Foam Sealant require solvents to clean up while they remain wet, or uncured. DAPtex, a latex foam, expands less and stays flexible as it dries -- and cleans up when uncured with soap and water. Uncured Uncured expanding foam remains wet and can pose a removal problem on skin, carpet or clothing. Polyurethane foam on rigid and soft surfaces: Consult the manufacturer's instructions, which will suggest solvents, such as acetone, paint thinner or nail polish, to remove uncured polyurethane foam. On soft surfaces, such as carpet, test an inconspicuous area first. Polyurethane foam on skin: Wipe off the foam with a paper towel, and rub off the final sticky layer with petroleum jelly or baby oil. Latex foam: DAPtex can be cleaned off surfaces and skin with soap and water. Cured Expanding foam dries and hardens in 1 to 8 hours, depending on the product. You can sand, trim or scrape cured foam from rigid surfaces. Use a utility knife with a new, sharp blade for overfill up to about 1 inch thick. Switch to a serrated bread knife for wider overfill. If polyurethane foam dries on your skin, rub off as much as you can with a pumice stone. After a week or so, any remaining dried flecks should work off your skin. Tip To clean the nozzle before putting away the expanding foam, home improvement expert Danny Lipford recommends inserting a spray lubricant straw into the nozzle and spraying lubricant through the nozzle, then cleaning out the nozzle with a wire. Wipe off the outside of the nozzle and the straw before storing them. Alternatively, clean the nozzle with a can of compressed air. A DAPtex nozzle can be cleaned with soap and water and a paper clip or pipe cleaner.
Homemade Rat and Mice Spray Repellent (with Pictures)One of the most popular techniques being used in roof insulation and roof repair is the spray foam roofing system. This technology has been around for many years and has been growing in popularity because of the many outstanding benefits and advantages over other types of roofing applications. When it comes to the foam material being used, most roofing contractors recommend polyurethane foam. To give you an idea what polyurethane foam is, it is a combination of two liquid elements- an isocyanate and polyolresin. They undergo a process of mixing according to its specified ratio which is normally one-is-to-one. The technique is applied by professional applicators using a team of spray foam equipment like a proportioner, heated hoses, transfer pumps and spray gun. Polyurethane foam is very flexible and versatile and can be applied to any type of roofing system. When the liquid polyurethane foam is sprayed over the affected roofing area, it expands and solidifies in just a matter of seconds. What happens next is you see a seamless and durable protective layer. The succeeding procedure is the application of another protective coating like an elastomeric type of coating. That is how simple sprayed polyurethane foam or SPF roofing system is. However, it is risky to undertake this procedure yourself if the extent of roofing repair and insulation is a bit complex. Adequate training, proper technique and application, and years of experience are the credentials brought in by the team of professional roofing repair and insulation contractors. It is the quality of work which will determine if the spray foam roofing will give the desired effects. If it is only the labor cost component you are trying to save when you decide to make it a do-it yourself job, you have to evaluate the situation thoroughly. On the other hand, if the roofing problem is a simple one and you are confident that you can do the procedure yourself, then go ahead. Having the basic technical know-how and skills and the energy are enough to accomplish the job. When it comes to DIY spray foam insulation kits, there are many types available in the market. The most common and affordable are the spray cans. You can shop in your local hardware stores for sealants and foam sprays and the price range depends on the features of the kits. You may want to purchase a kit with a pressurized spray nozzle or spray gun with extra nozzle tips and foaming chemicals. Before you buy what you need, try to familiarize yourself with the best type of kit by learning the appropriate ingredients and other matters such as r-value and other resistance rating. As soon as you are able to buy your kit, the next step is to see to it that the area to be worked on is perfectly clean and free of any debris. Just follow the instruction guideline in the manner of spray technique. The actual schedule should be done when you believe that the weather won't be a problem. For an ideal application, you have to do the spray foam roofing at the right temperature. If your roofing needs an extensive protection and insulation, it is to your best interest to assign the work to the professionals. Do your homework as to which type of foam material you consider the best. If you choose the SPF system together with a reputable elastomeric brand of coating, all you need to do is to finalize a deal with a dependable roofing and thermal insulation contractor for a total project cost within your budget. The bottom line is your house will enjoy proper room temperature during hot or cold days, some sound and noise reduction, wind lift, flame and weather resistance. There are other benefits you will enjoy not limited to reduced energy bills. In effect, the project investment you make is a self-liquidating one. Because of lower energy consumption, you are also helping out in the government's energy security and environmental concerns. What is of prime importance is the big picture. Just visualize the peace of mind, comfort and enjoyment spray foam roofing will provide to your family for many years to come!