Broadmoor The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as “Open Cell” because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the “open” space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across a spray foam insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam.
Can You Paint Slate Tiles?Today, more and more emphasis is being placed on having an energy-efficient home. More people are recognizing that resources are limited and each person needs to make an individual effort to reduce the amount of energy they use. Most residents in the United States live in areas where there are at least two distinct seasons. Winters are often cold and icy, and indoor heating is required for a comfortable living environment. In the summer months, temperatures can get very hot and many homes use air conditioning to keep the environment cool. Using heating or cooling systems takes up a huge amount of energy. You, therefore, want to make sure that the warm or cool air is being retained in your home. If not, a large amount of energy is being wasted. This is where insulation becomes important. How Good Insulation Improves the Energy Efficiency of Your Home Good insulation, especially in your roof, can make a huge difference in the energy efficiency of your home. It keeps the warm air circulating in your home which means that you do not need to use excess energy to keep heat in your home. You will never be able to insulate your home completely; in fact, it would be unhealthy to do so. You can, however, use good insulation to help slow the convection and reduction effect so you are not making your heating system work harder than it should be. This refers to the rate at which heat escapes from your home or the way in which the flow of hot air into your home during the summer months can greatly reduce the effectiveness of your cooling system. What Is the Measure of a Good Insulator? In the building and construction industry, an R-rating is used to rank the effectiveness of an insulating material. The rating looks at how well the insulator repels cold or heat, prevents the flow of air from one area to another, and how well it manages to retain an ambient temperature in a certain environment. When you compare the R-rating of spray foam against other types of insulators, you can start to see why it is considered to be such a great insulator. In terms of an R-ratting, most spray foams rate between 6 and 7.7. Open cell types of spray foam may have a rating as low as 4. Another typical type of insulator that is used in many homes in fiberglass matting. This has an R-rating of only 3.5. When compared to spray foam, you can see how even the lowest level of spray foam insulation is far more effective than fiberglass mats. Added Benefits of Using Spray Foam as an Insulator There can be little doubt that spray foam is a great insulator but is it really the best option for your home? What about the installation and the cost? Spray foam may initially seem to be a more expensive insulation option but you need to look at it from a long-term perspective. It is an incredibly durable substance. When applied properly, it can last for many years. It is also far more resistant to the buildup of moisture and mold, making your home a safer environment to live in. Spray foam will not break apart or wear down over time in the same way fiberglass mats do. Once applied, it will outlast most other forms of insulation. Spray foam can also help to strengthen walls and the structure of your home. It can be applied to small crawlspaces and hard-to-reach cracks. In this way, it can help keep insects and vermin out of your home. To apply spray foam to your home, there are a number of options available. You can choose an option that suits your budget and the time you have available to manage the project. If you are quite handy with DIY projects, you can buy a spray foam kit online. It comes will all the necessary components and safety gear and has easy-to-follow instructions. You can apply it yourself and save yourself some money if you have the time available to take on the project. If you are less confident in your ability to apply the spray foam yourself, then you can use the services of a professional contractor. They can be in and out of your home in a matter of hours or days, depending on the size of a project.
How to Make a Spray Foam TreeOne of the most important keys to reducing your heating and cooling costs is having your home well-insulated. So what is the best insulation for your home? Spray Foam Foam insulation has two forms: Open and closed cell. Both are made from a polyurethane material and have different propellant agents added. Some are made from biodegradable materials, such as soybeans, to make the off-gases friendlier to the environment. Foam is probably the best insulation for blocking air infiltration combined with high R-value. Installed by a professional, the price of spray foam varies depending on the thickness of the walls and type of foam. Spray foam insulation is probably the best overall insulation on the market if you can afford the cost. Foam insulation lowers your heating and your cooling loads when installed correctly. Additional benefits are elimination of air infiltration, keeps out dust, mold and allergens, and does not sag or deteriorate. Open cell foam is used more in residential applications. It is less expensive to install and is easier to work with after it's in place. Open cell allows water to penetrate, so it makes an excellent roof deck insulator. If water is allowed to penetrate, you can locate roof leaks before the decking deteriorates. Biggest benefit of open cell is heat transfer in sunny locations. It takes approximately 36 hours of sun to penetrate through 8 inches of foam. This is also true for walls. So when the home is cooled, it will stay cool. The warranty of the roof material is not voided with the installation of spray foam insulation. Closed cell foam has a much more structural component to it and can support some weight without compression. Closed cell does not allow water to penetrate and is an excellent insulator for basement and crawl walls where water could be a problem. Closed cell foam has a higher R-value per inch but is very ridged and tough to work with after installation. It is most often used in commercial applications. However, it has its useful applications in homes. Foam insulation keeps mold out of walls. Mold occurs in walls with batt insulation because of "thermal loop effect". This is where the heat penetrates the exterior wall, coming in contact with the cooler interior surface of the drywall, causing moisture to form. Moisture above 25% can provide an environment for mold to grow. Spray foam blocks this heat transfer and has no air gaps in which moisture can form. One way to combat the higher cost of spray foam is to combine a couple of inches of closed cell foam with fiberglass batt insulation installed over the foam, getting the exceptional air-blocking value of foam, with the high R-value and lower cost of fiberglass insulation. Spray foam insulation costs more than fiberglass batts, but it also has approximately twice the R-value of typical fiberglass batts insulation. By combining the two you will get the best of both. Foam insulation is also particularly good for remodeling projects when there is only easy access to the basement or crawl space and the attic. By blocking the air flow from the top (attic) and bottom (crawl or basement) you stop the draftiness that some older homes have, thus making the home more comfortable. A more comfortable home is what we all are looking to achieve. Spray foam can give you warmth in the winter and cooling in the summer when combined with the appropriate HVAC system. These systems can be smaller in size when your home is better insulated with less air infiltration.
How to Remove Expanding Foam Residue With a SolventThermal Spray Foam Insulation is used in buildings, and refers to the application of thermal insulated materials, which are applied using various spraying methods, into a roof space or wall cavity to prevent heat loss. The application of this process is normally completed within two days. Thermal spray foam insulation does not particularly address ventilation or sound proofing issues. It simply refers to the insulating materials being used to slow heat loss. The effectiveness of it is usually evaluated by its R-value, but this does not take into account construction or local environment factors. Thermal spray foam insulation is easy to apply. Foam insulation is sprayed onto or into the underside of the roof within the attic/loft space, and dries to a rigid foam. Thermal spray foam insulation is an important factor to achieving thermal comfort for the buildings occupants, and thermal spray foam insulation reduces unwanted heat loss, and reduces the energy requirements of cooling and heating systems. Thermal spray foam insulation simply refers to the insulating materials being used to slow heat loss. One of the most effective types of insulation spray is polyurethane foam, which has been specifically formulated for use within the insulation industry. This type of foam is a very cost effective insulation material, and works in two ways by keeping the desired space or area warm in winter and cool in the summer. It can also help with the problems that arise from condensation, and is an ideal solution for ambient and cold storage. Polyurethane foam is easy to apply, lightweight in structure and can cover large areas quickly and efficiently, making it a very cost effective solution for many commercial requirements. The application of foam spray uses a rigid polyurethane foam which sprays to a fine cellular structure with high compressive strength and good adhesion and insulating qualities. Many of these foam spraying techniques and materials do not contain or use any CFCs. Thermal spray foam insulation will adhere to most structures and other materials such as fibre, sheet metal, cement, asbestos sheeting, concrete and steel. When sprayed it can expand to over thirty times it thickness. It is lightweight in structure, weighing only three kilos per square metre at a depth of fifty millimetres. (approx) Insulating a building with this method will help to keep it warm in the summer and cool in the winter, reducing temperature control costs and providing a dry and comfortable environment for staff and workforce, and controlled storage for stock and materials.