McCordsville The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as “Open Cell” because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the “open” space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across a spray foam insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam.
How to Remove Expanding Foam Residue With a SolventPolyurethane foam (PUR foam) had been widely used in most household and building installations. There are two types of polyurethane depending on how it is applied, the rigid form and the spray foam. Spray foam application is usually cheaper though less effective. Polyurethane foam is an insulation material with high thermal resistance because of the low-conductivity gas present. It is available in liquid formed but is applied using a spray equipment. HCFC or hydro chlorofluorocarbons are the usual gas used with an R-value range of R-7 to R-8 per inch. This R-value deteriorates in time through the process called thermal drift. As the low conductivity gas escapes through the air, gas molecules present in air replaces the gases in the insulation. This phenomenon usually starts after 2 years of installation. While the rigid board structure is more effective in insulating, application of spray polyurethane foam insulation relatively is easy since it molds to the form of the surface. Because of that it is also called, foamed-in-application. Most of the spray foam produce today has non-CFC (non-chlorofluorocarbon) gas as their foaming agent. While these non-CFC foams are less effective in insulation, they pose less threat to the ozone layer. It is also effective in a relative large range of temperature. An R-value of R-6 to R-6.5 per inch is normal for high density closed-cell PUR foam, about 32 kilograms per cubic meter (kg/m3). Low density open-cell PUR foam has about 8 kilogram per cubic meter (kg/m3). This has been noted to be more flexible than the regular polyurethane foams. Carbon dioxide as also been used as a forming agent for some low density foams. Spraying the polyurethane foam requires specific equipment and personnel using them must be properly trained. High density foams have usually slow-expanding capabilities. Low density foams expand rapidly when applied to walls' cavity sealing them almost instantly. However may cause over-expansion in the walls' surfaces creating damage. Using spray polyurethane foams in home insulation benefits the owner in many ways. Non-CFC foams are eco-friendly have no formaldehydes that may damage the ozone layer in the atmosphere. It can greatly eliminate air or wind infiltration the household. Air seeping through cracks or opening in the walls or roofing can increase convective air currents in attics or walls and also increase moisture and condensation rate inside the household. Since it is a very effective insulation, less energy can be used in terms of cooling and heating the household, while maintain the preferred comfort zone inside the house. It also passively strengthens the walls they are applied to. It has also long life span of more than 10 years which can be extended further by recoating. Installing or using spray polyurethane foam insulation, however must depend and customize to fit the home's building lay-out, cost of effectiveness, and even the climate wherein the home stands. While these considerations can be easily dealt with especially for someone with high budget, application of spray foam polyurethane, for best results must be left at the hands of experts.
How to Remove Spray Foam InsulationSo, you have chosen to kick out the pink stuff and insulate your home using polyurethane foam insulation instead. Congratulations! You're on your way to reaping the benefits of more energy savings, less mold, fewer air leaks, greener materials, and twice the protective capability when compared to traditional fiberglass and cellulose insulation. But you won't see these advantages if you do not apply spray foam insulation properly - and that begins before you start spraying. Before you even think about moving forward, you should be thinking about safety. Protective safety goggles, full-cover clothing, a mask, and work gloves are a must for anyone applying expanding foam insulation. Make absolutely sure that no skin is exposed during application, because the adhesiveness of spray foam is similar to that of permanent glue: it will stick to skin and will not come off. If this occurs, the insulation will remain on your skin until your outer epidermal layer peels off. For the record, the only substances known to remove expanding foam are white spirit-based solvents - and only then if the insulation has not begun to set. Applying polyurethane foam insulation also opens the possibility of the material getting into your lungs, which can cause respiratory problems. In short, get confident in your ability to apply spray foam properly. Once you are ready to proceed, make sure the area where the spray foam is to be applied is between 65 and 80 degrees Fahrenheit. If it is not, either wait for the temperatures to decrease or warm the area using a bullet heater. Also, make sure the application area is clear of debris and dust in order to maximize adhesion. If there are holes or cracks in the walls or ceiling areas where you are spraying, make sure that you apply a sealant to insure a suitable air seal. Once the area to be sprayed is ready, you must turn your attention to the areas that will not be sprayed. Windows, doors, floors, drywall, and other areas must be masked with cloth or plastic sheeting so they won't be affected by over spraying. If there are any objects or structures that cannot be removed before spraying (such as air conditioners, plumbing piping, or heating units), then make sure they are completely covered as well. Again, one gap in your protective sheeting could result in a spot or stain which you may be unable to remove.
How to Remove Spray Foam InsulationWhen you're planning to complete any home remodeling or building project, you'll need to understand the insulation needs for your particular venture. While traditional insulation certainly has its place in modern construction, it is often not the best choice. Spray foam is actually a better choice in many circumstances, giving you more effective insulation at a lower cost. Foam is an efficient method for insulating your home, and it presents a number of advantages over more traditional insulation materials. There are, of course, some downsides to the use of spray foam in certain cases, and understanding the pros and cons associated with your insulation choices will help you make the appropriate decisions for all of your projects. Foam is an extremely efficient insulating material. It excels at blocking heat, and helps prevent excessive heat from entering the home. It can also help keep the internal temperature steady, preventing heated or cooled air from escaping the home as well. The measure of a material's ability to maintain the internal temperature of your home is actually called the R-value, and represents the material's effectiveness in blocking heat. The R-value represents the amount of heat or energy the material can block, measured against the space of the material. With spray foam, the R-value is very high, making it a highly effective method for insulating large spaces. The nature of spray foam additionally makes it a good choice for adding insulation to existing spaces. Those locations in your home that are in need of new insulation can be tricky to update. Removing walls, ceilings or floor materials in an effort to add new insulation to an existing area means a great deal of work and expense. Spray foam insulation can get these types of jobs done more quickly and with less money invested in construction efforts. Spray foam makes many jobs easier as it can be placed within existing walls and other spaces without requiring access to the entire space. The foam can be sprayed into the space through small openings and then expands to fill the space with the same or better effectiveness as that obtained from a more traditional insulation material. One of the potential downsides of spray foam insulation is that it can cost more upfront than other insulation options. When working with a limited immediate budget, you may need to consider less costly options for your projects; however, you always want to keep in mind the long-term financial implications of any of your construction, home improvement, or home maintenance choices. While installing spray foam insulation in your home can be more expensive upfront than some other insulation options, it is a more cost-efficient long-term solution to insulation needs. Not only does it eliminate some of the costs associated with installing new insulation, by making the process more effective through less invasive methods, but it also gives you highly efficient insulation for years to come. The process of installing other forms of insulation in existing walls and other less accessible regions of the home can result in additional construction costs, as you must remove and replace sections of the wall, floor or ceiling in order to gain access to the areas that are in need of new insulation. By using spray foam, you remove most of the costs associated with accessing hard-to-reach areas. The R-value efficiency of spray foam makes it a good long-term investment. The upfront cost of installation may be slightly higher than with other materials but the savings in home heating and cooling costs in the long run can make spray foam a more effective and efficient choice. Additionally, you should consider using spray foam in those areas of the home that have crevices, cracks, gaps or holes present. Traditional insulation materials don't reach these types of locations with the same efficiency as spray foam. Air and moisture can get trapped in such spaces, presenting issues with heating and cooling your home effectively. Trapped air and moisture make it more difficult to keep internal temperatures steady. Poor insulation allows external temperatures to leak into the home and internal temperatures to escape to the outdoors. Moisture and condensation that can build up in the cracks, gaps and other empty spaces in the walls, floors, and ceilings in your home can lead to other problems as well. Mold and mildew can result from trapped moisture, presenting issues with not only the efficient heating and cooling of your home but with the quality of the internal air as well. Health concerns surrounding these invasive pests can be serious, and the effort and cost involved in removing mold and mildew greatly exceeds those associated with preventing them in the first place. By using spray foam insulation, you limit the chances of air building up in unfilled spaces within the structure of your home. You also eliminate the concerns associated with moisture being trapped in these types of spaces.