New Palenstine Spray Foam Exterior Walls

New Palenstine The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as “Open Cell” because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the “open” space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across a spray foam insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam.

Indiana Spf Insulation

How to Remove Expanding Foam

Open Cell Foam Spray Is polyurethane foam, in its sprayed form and as an insulator, actually environmentally friendly? What does 'green' and 'environmentally friendly' mean? All excellent questions, and all of them are not answerable in a word or two. Let's begin with defining the concept of environmentally friendly. According to the International Organization for Standardization (IOS) the term is too vague to be meaningful. The US Environmental Protection Agency (USEPA) agrees, but only to a point. The USEPA created the international Energy Star program in an attempt to provide the manufacturers of goods with a voluntary labeling system for promoting energy efficient products. In the 1990's when the program was started, it was only applied to appliances and electronics. However, today entire homes and home offices are able to gain Energy Star certification. The only criteria is the building must use 15% less energy than a standard home built to the 2004 International Residential Code. How does a home achieve that rating? The things at the top of the list for getting an Energy Star rating are not surprising: insulation, high performance windows, tight construction and ducting, energy efficient cooling and heating systems and Energy Star certified products (appliances, lighting, water heaters). Now, in reference to insulation specifically, its efficiency is measured according to R-value. An R-value is a mathematical calculation which produces the level of thermal resistance a building has. For the average North American home insulated with traditional fiberglass batts, R-value sits at between 3.1 and 4.3 per square inch. Blown in fiberglass insulation has a typical R-value between 2 and 4 per square inch. According to the US Department of Energy, the same home insulated with spray foam polyurethane insulation will have an R-value between 7 and 8 per square inch. Clearly a home insulated with spray foam would be well on its way to achieving an Energy Star rating, even without installing LED lighting and thermal windows. When a building is insulated with polyurethane foam, the costs of heating and cooling will undoubtedly be vastly reduced. Many spray foam manufacturers report that energy costs can be reduced by up to 40%; a claim that is both highly likely and easily attainable. With such a diminished use of energy, there is less demand for petroleum-based products and fossil fuels, resulting in a smaller carbon footprint being left on our planet. We are half way to answering our title question, is spray foam insulation really green? Now we know its immense potential for energy savings, but what about the manufacture of the foam itself? In the case of spray foam, the two substances that come together to produce the foam must remain separate until the time of application. Those two things are polyol (a naturally occurring alcohol) and diisocyanate (a group of organic compounds derived from plant and animal materials). When they are brought together with water, an exothermic reaction takes place producing the polyurethane foam. Although the foam is produced from organic substances, it does not breakdown over time - a good thing for insulation applications, but where does it go when it is no longer needed? When the intended use of the polyurethane foam has been completed, it can be re-purposed and recycled. For example, the Polyurethane Foam Association has pioneered a program in the US in which spray foam insulation and products meant for the landfill are collected and made into carpet foam underlay. The program is so successful that 80% of all carpet underlay used in the US is made from recycled polyurethane foam. The reduction in waste going to landfills is incredible! So, is spray foam insulation really 'green'? Yes, it is. Polyurethane foam is produced in an environmentally friendly way in that it is created from organic compounds using very little energy or water, prevents the excess use of fuel in heating and cooling homes and is entirely recyclable for other uses.

How to Make a Spray Foam Tree

Spray Foam Basement Expanding foam that overexpands and lands where you didn't plan for it -- on hands, clothes, cinderblock or studs -- can pose a removal problem, with the solution depending on the type you use. Polyurethane foams including Dow's Great Stuff, Touch 'n Foam, DAP Kwik Foam and Owens-Corning Insulating Foam Sealant require solvents to clean up while they remain wet, or uncured. DAPtex, a latex foam, expands less and stays flexible as it dries -- and cleans up when uncured with soap and water. Uncured Uncured expanding foam remains wet and can pose a removal problem on skin, carpet or clothing. Polyurethane foam on rigid and soft surfaces: Consult the manufacturer's instructions, which will suggest solvents, such as acetone, paint thinner or nail polish, to remove uncured polyurethane foam. On soft surfaces, such as carpet, test an inconspicuous area first. Polyurethane foam on skin: Wipe off the foam with a paper towel, and rub off the final sticky layer with petroleum jelly or baby oil.  Latex foam: DAPtex can be cleaned off surfaces and skin with soap and water. Cured Expanding foam dries and hardens in 1 to 8 hours, depending on the product. You can sand, trim or scrape cured foam from rigid surfaces. Use a utility knife with a new, sharp blade for overfill up to about 1 inch thick. Switch to a serrated bread knife for wider overfill. If polyurethane foam dries on your skin, rub off as much as you can with a pumice stone. After a week or so, any remaining dried flecks should work off your skin. Tip To clean the nozzle before putting away the expanding foam, home improvement expert Danny Lipford recommends inserting a spray lubricant straw into the nozzle and spraying lubricant through the nozzle, then cleaning out the nozzle with a wire. Wipe off the outside of the nozzle and the straw before storing them. Alternatively, clean the nozzle with a can of compressed air. A DAPtex nozzle can be cleaned with soap and water and a paper clip or pipe cleaner.

How to Remove Expanding Foam

Blown In Insulation Cost Polyurethane foam (PUR foam) had been widely used in most household and building installations. There are two types of polyurethane depending on how it is applied, the rigid form and the spray foam. Spray foam application is usually cheaper though less effective. Polyurethane foam is an insulation material with high thermal resistance because of the low-conductivity gas present. It is available in liquid formed but is applied using a spray equipment. HCFC or hydro chlorofluorocarbons are the usual gas used with an R-value range of R-7 to R-8 per inch. This R-value deteriorates in time through the process called thermal drift. As the low conductivity gas escapes through the air, gas molecules present in air replaces the gases in the insulation. This phenomenon usually starts after 2 years of installation. While the rigid board structure is more effective in insulating, application of spray polyurethane foam insulation relatively is easy since it molds to the form of the surface. Because of that it is also called, foamed-in-application. Most of the spray foam produce today has non-CFC (non-chlorofluorocarbon) gas as their foaming agent. While these non-CFC foams are less effective in insulation, they pose less threat to the ozone layer. It is also effective in a relative large range of temperature. An R-value of R-6 to R-6.5 per inch is normal for high density closed-cell PUR foam, about 32 kilograms per cubic meter (kg/m3). Low density open-cell PUR foam has about 8 kilogram per cubic meter (kg/m3). This has been noted to be more flexible than the regular polyurethane foams. Carbon dioxide as also been used as a forming agent for some low density foams. Spraying the polyurethane foam requires specific equipment and personnel using them must be properly trained. High density foams have usually slow-expanding capabilities. Low density foams expand rapidly when applied to walls' cavity sealing them almost instantly. However may cause over-expansion in the walls' surfaces creating damage. Using spray polyurethane foams in home insulation benefits the owner in many ways. Non-CFC foams are eco-friendly have no formaldehydes that may damage the ozone layer in the atmosphere. It can greatly eliminate air or wind infiltration the household. Air seeping through cracks or opening in the walls or roofing can increase convective air currents in attics or walls and also increase moisture and condensation rate inside the household. Since it is a very effective insulation, less energy can be used in terms of cooling and heating the household, while maintain the preferred comfort zone inside the house. It also passively strengthens the walls they are applied to. It has also long life span of more than 10 years which can be extended further by recoating. Installing or using spray polyurethane foam insulation, however must depend and customize to fit the home's building lay-out, cost of effectiveness, and even the climate wherein the home stands. While these considerations can be easily dealt with especially for someone with high budget, application of spray foam polyurethane, for best results must be left at the hands of experts.

 


Indiana