Wynndale Cellular Foam Insulation

Wynndale The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as “Open Cell” because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the “open” space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across a spray foam insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam.

Indiana Spf Insulation

How to Upholster Bar Stools

Spray Foam Roof Insulation Cost One of the most important keys to reducing your heating and cooling costs is having your home well-insulated. So what is the best insulation for your home? Spray Foam Foam insulation has two forms: Open and closed cell. Both are made from a polyurethane material and have different propellant agents added. Some are made from biodegradable materials, such as soybeans, to make the off-gases friendlier to the environment. Foam is probably the best insulation for blocking air infiltration combined with high R-value. Installed by a professional, the price of spray foam varies depending on the thickness of the walls and type of foam. Spray foam insulation is probably the best overall insulation on the market if you can afford the cost. Foam insulation lowers your heating and your cooling loads when installed correctly. Additional benefits are elimination of air infiltration, keeps out dust, mold and allergens, and does not sag or deteriorate. Open cell foam is used more in residential applications. It is less expensive to install and is easier to work with after it's in place. Open cell allows water to penetrate, so it makes an excellent roof deck insulator. If water is allowed to penetrate, you can locate roof leaks before the decking deteriorates. Biggest benefit of open cell is heat transfer in sunny locations. It takes approximately 36 hours of sun to penetrate through 8 inches of foam. This is also true for walls. So when the home is cooled, it will stay cool. The warranty of the roof material is not voided with the installation of spray foam insulation. Closed cell foam has a much more structural component to it and can support some weight without compression. Closed cell does not allow water to penetrate and is an excellent insulator for basement and crawl walls where water could be a problem. Closed cell foam has a higher R-value per inch but is very ridged and tough to work with after installation. It is most often used in commercial applications. However, it has its useful applications in homes. Foam insulation keeps mold out of walls. Mold occurs in walls with batt insulation because of "thermal loop effect". This is where the heat penetrates the exterior wall, coming in contact with the cooler interior surface of the drywall, causing moisture to form. Moisture above 25% can provide an environment for mold to grow. Spray foam blocks this heat transfer and has no air gaps in which moisture can form. One way to combat the higher cost of spray foam is to combine a couple of inches of closed cell foam with fiberglass batt insulation installed over the foam, getting the exceptional air-blocking value of foam, with the high R-value and lower cost of fiberglass insulation. Spray foam insulation costs more than fiberglass batts, but it also has approximately twice the R-value of typical fiberglass batts insulation. By combining the two you will get the best of both. Foam insulation is also particularly good for remodeling projects when there is only easy access to the basement or crawl space and the attic. By blocking the air flow from the top (attic) and bottom (crawl or basement) you stop the draftiness that some older homes have, thus making the home more comfortable. A more comfortable home is what we all are looking to achieve. Spray foam can give you warmth in the winter and cooling in the summer when combined with the appropriate HVAC system. These systems can be smaller in size when your home is better insulated with less air infiltration.

How to Remove Expanding Foam

Commercial Spray Foam Insulation After long hours of searching you have finally landed in the right place. At last the elusive answers to questions on insulation and spray foam are here awaiting your approval. These aren't the usual newbie FAQ's. These are the 'technical' questions only the really savvy home renovators ask. No more intense bouts of frustration where you suddenly find you're banging your head on the keyboard. The real answers to the advanced questions are here, so say goodbye to impressions of little squares on the forehead. Does spray foam release any Volatile Organic Compounds (VOC)? Polyurethane foam is not considered to emit VOC's. However, during application some spray foams release VOC's through the process of discharge from the canister. After curing there should not be any further emissions. To be sure, check with your foam supplier. Can it be used to insulate underground water pipes? Yes! Work closely with the polyurethane manufacturer to determine the best method of application and the most beneficial kind of foam to use. Regional climate changes and projected temperature extremes will be a part of the decision making process. During application, be sure to prepare the trench properly so that no moisture is allowed on or in the foam until it has cured. Should fibreglass insulation be removed before applying it? Yes! Many contractors opt for leaving blown in insulation in an attic and spraying the foam on top. The problem that arises is ventilation and temperature control. More clearly, the temperature of the attic floor will be different than amidst the fibreglass and the temperature amidst the fibreglass will be different than above the spray foam. The job of the spray foam is to balance temperature and humidity with the environment so condensation is prevented. With an inner layer of fibreglass, where air flows, the conditions would be perfect for moisture formation. Does the surface where it will be applied have to be clean? Yes! Any oil or dust on the application surface will prevent the spray foam from adhering. For the typical attic in a wood frame home, a careful vacuuming job covering every nook and cranny will often be adequate. For applications where the surface is steel (or any other metal) it is even more important for the surface to be free of dust and oil. In some cases where the steel is very new, a coat of primer will be required. Many spray foam manufacturers offer a simple rule: if it can be painted, it can be spray foamed. Does an attic need to be vented if spraying foam on the rafters? That depends. If you are applying the spray foam to the roof deck and gable walls, then you want everything under that surface to be a part of the temperature conditioned space. Vents in an attic with insulation above it would be much like have open windows year round - a total waste of money. If you are applying spray foam to just the attic floor, then the conditioned space is below the attic floor. Vents will be necessary for preventing excess humidity. Is weather a factor when applying it? Water is the most important consideration, either as rain or condensation. If there is any moisture present on the application surface, the spray foam will not adhere. Most of the time the problem will be seen right away, and the installer can stop the job until the surface is dry. In the case of applying spray foam to the exterior of roofs and walls during the construction process, wind will be a major factor as well. Overspray carried by wind can not only affect surrounding surfaces, it can mean a loss of yield. Ambient temperature plays a role as well, albeit in extreme conditions. Exceptionally hot temperatures can cause the foam to not hold shape, cause risk to the installer in enclosed hot places and even risk explosion of the tanks holding the polyurethane. Freezing temperatures, such as in northern Alaska, may cause the applicator to cease working altogether. The substrate temperature is a factor as well. For unique situations such as these, it is best to consult with the manufacturer to see how best to proceed.

How to Remove Expanding Foam

Spray Insulation Under House Is polyurethane foam, in its sprayed form and as an insulator, actually environmentally friendly? What does 'green' and 'environmentally friendly' mean? All excellent questions, and all of them are not answerable in a word or two. Let's begin with defining the concept of environmentally friendly. According to the International Organization for Standardization (IOS) the term is too vague to be meaningful. The US Environmental Protection Agency (USEPA) agrees, but only to a point. The USEPA created the international Energy Star program in an attempt to provide the manufacturers of goods with a voluntary labeling system for promoting energy efficient products. In the 1990's when the program was started, it was only applied to appliances and electronics. However, today entire homes and home offices are able to gain Energy Star certification. The only criteria is the building must use 15% less energy than a standard home built to the 2004 International Residential Code. How does a home achieve that rating? The things at the top of the list for getting an Energy Star rating are not surprising: insulation, high performance windows, tight construction and ducting, energy efficient cooling and heating systems and Energy Star certified products (appliances, lighting, water heaters). Now, in reference to insulation specifically, its efficiency is measured according to R-value. An R-value is a mathematical calculation which produces the level of thermal resistance a building has. For the average North American home insulated with traditional fiberglass batts, R-value sits at between 3.1 and 4.3 per square inch. Blown in fiberglass insulation has a typical R-value between 2 and 4 per square inch. According to the US Department of Energy, the same home insulated with spray foam polyurethane insulation will have an R-value between 7 and 8 per square inch. Clearly a home insulated with spray foam would be well on its way to achieving an Energy Star rating, even without installing LED lighting and thermal windows. When a building is insulated with polyurethane foam, the costs of heating and cooling will undoubtedly be vastly reduced. Many spray foam manufacturers report that energy costs can be reduced by up to 40%; a claim that is both highly likely and easily attainable. With such a diminished use of energy, there is less demand for petroleum-based products and fossil fuels, resulting in a smaller carbon footprint being left on our planet. We are half way to answering our title question, is spray foam insulation really green? Now we know its immense potential for energy savings, but what about the manufacture of the foam itself? In the case of spray foam, the two substances that come together to produce the foam must remain separate until the time of application. Those two things are polyol (a naturally occurring alcohol) and diisocyanate (a group of organic compounds derived from plant and animal materials). When they are brought together with water, an exothermic reaction takes place producing the polyurethane foam. Although the foam is produced from organic substances, it does not breakdown over time - a good thing for insulation applications, but where does it go when it is no longer needed? When the intended use of the polyurethane foam has been completed, it can be re-purposed and recycled. For example, the Polyurethane Foam Association has pioneered a program in the US in which spray foam insulation and products meant for the landfill are collected and made into carpet foam underlay. The program is so successful that 80% of all carpet underlay used in the US is made from recycled polyurethane foam. The reduction in waste going to landfills is incredible! So, is spray foam insulation really 'green'? Yes, it is. Polyurethane foam is produced in an environmentally friendly way in that it is created from organic compounds using very little energy or water, prevents the excess use of fuel in heating and cooling homes and is entirely recyclable for other uses.

 


Indiana