Indianapolis Poly Foam Insulation

Indianapolis The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as “Open Cell” because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the “open” space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across a spray foam insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam.

Indiana Spf Insulation

How to Upholster Bar Stools

Spray Foam Sealant Polyurethane foam (PUR foam) had been widely used in most household and building installations. There are two types of polyurethane depending on how it is applied, the rigid form and the spray foam. Spray foam application is usually cheaper though less effective. Polyurethane foam is an insulation material with high thermal resistance because of the low-conductivity gas present. It is available in liquid formed but is applied using a spray equipment. HCFC or hydro chlorofluorocarbons are the usual gas used with an R-value range of R-7 to R-8 per inch. This R-value deteriorates in time through the process called thermal drift. As the low conductivity gas escapes through the air, gas molecules present in air replaces the gases in the insulation. This phenomenon usually starts after 2 years of installation. While the rigid board structure is more effective in insulating, application of spray polyurethane foam insulation relatively is easy since it molds to the form of the surface. Because of that it is also called, foamed-in-application. Most of the spray foam produce today has non-CFC (non-chlorofluorocarbon) gas as their foaming agent. While these non-CFC foams are less effective in insulation, they pose less threat to the ozone layer. It is also effective in a relative large range of temperature. An R-value of R-6 to R-6.5 per inch is normal for high density closed-cell PUR foam, about 32 kilograms per cubic meter (kg/m3). Low density open-cell PUR foam has about 8 kilogram per cubic meter (kg/m3). This has been noted to be more flexible than the regular polyurethane foams. Carbon dioxide as also been used as a forming agent for some low density foams. Spraying the polyurethane foam requires specific equipment and personnel using them must be properly trained. High density foams have usually slow-expanding capabilities. Low density foams expand rapidly when applied to walls' cavity sealing them almost instantly. However may cause over-expansion in the walls' surfaces creating damage. Using spray polyurethane foams in home insulation benefits the owner in many ways. Non-CFC foams are eco-friendly have no formaldehydes that may damage the ozone layer in the atmosphere. It can greatly eliminate air or wind infiltration the household. Air seeping through cracks or opening in the walls or roofing can increase convective air currents in attics or walls and also increase moisture and condensation rate inside the household. Since it is a very effective insulation, less energy can be used in terms of cooling and heating the household, while maintain the preferred comfort zone inside the house. It also passively strengthens the walls they are applied to. It has also long life span of more than 10 years which can be extended further by recoating. Installing or using spray polyurethane foam insulation, however must depend and customize to fit the home's building lay-out, cost of effectiveness, and even the climate wherein the home stands. While these considerations can be easily dealt with especially for someone with high budget, application of spray foam polyurethane, for best results must be left at the hands of experts.

How to Fix Holes in Tree Trunks

Spray Foam Cost Is polyurethane foam, in its sprayed form and as an insulator, actually environmentally friendly? What does 'green' and 'environmentally friendly' mean? All excellent questions, and all of them are not answerable in a word or two. Let's begin with defining the concept of environmentally friendly. According to the International Organization for Standardization (IOS) the term is too vague to be meaningful. The US Environmental Protection Agency (USEPA) agrees, but only to a point. The USEPA created the international Energy Star program in an attempt to provide the manufacturers of goods with a voluntary labeling system for promoting energy efficient products. In the 1990's when the program was started, it was only applied to appliances and electronics. However, today entire homes and home offices are able to gain Energy Star certification. The only criteria is the building must use 15% less energy than a standard home built to the 2004 International Residential Code. How does a home achieve that rating? The things at the top of the list for getting an Energy Star rating are not surprising: insulation, high performance windows, tight construction and ducting, energy efficient cooling and heating systems and Energy Star certified products (appliances, lighting, water heaters). Now, in reference to insulation specifically, its efficiency is measured according to R-value. An R-value is a mathematical calculation which produces the level of thermal resistance a building has. For the average North American home insulated with traditional fiberglass batts, R-value sits at between 3.1 and 4.3 per square inch. Blown in fiberglass insulation has a typical R-value between 2 and 4 per square inch. According to the US Department of Energy, the same home insulated with spray foam polyurethane insulation will have an R-value between 7 and 8 per square inch. Clearly a home insulated with spray foam would be well on its way to achieving an Energy Star rating, even without installing LED lighting and thermal windows. When a building is insulated with polyurethane foam, the costs of heating and cooling will undoubtedly be vastly reduced. Many spray foam manufacturers report that energy costs can be reduced by up to 40%; a claim that is both highly likely and easily attainable. With such a diminished use of energy, there is less demand for petroleum-based products and fossil fuels, resulting in a smaller carbon footprint being left on our planet. We are half way to answering our title question, is spray foam insulation really green? Now we know its immense potential for energy savings, but what about the manufacture of the foam itself? In the case of spray foam, the two substances that come together to produce the foam must remain separate until the time of application. Those two things are polyol (a naturally occurring alcohol) and diisocyanate (a group of organic compounds derived from plant and animal materials). When they are brought together with water, an exothermic reaction takes place producing the polyurethane foam. Although the foam is produced from organic substances, it does not breakdown over time - a good thing for insulation applications, but where does it go when it is no longer needed? When the intended use of the polyurethane foam has been completed, it can be re-purposed and recycled. For example, the Polyurethane Foam Association has pioneered a program in the US in which spray foam insulation and products meant for the landfill are collected and made into carpet foam underlay. The program is so successful that 80% of all carpet underlay used in the US is made from recycled polyurethane foam. The reduction in waste going to landfills is incredible! So, is spray foam insulation really 'green'? Yes, it is. Polyurethane foam is produced in an environmentally friendly way in that it is created from organic compounds using very little energy or water, prevents the excess use of fuel in heating and cooling homes and is entirely recyclable for other uses.

How to Paint Rope

Blown In Insulation Cost One of the most important keys to reducing your heating and cooling costs is having your home well-insulated. So what is the best insulation for your home? Spray Foam Foam insulation has two forms: Open and closed cell. Both are made from a polyurethane material and have different propellant agents added. Some are made from biodegradable materials, such as soybeans, to make the off-gases friendlier to the environment. Foam is probably the best insulation for blocking air infiltration combined with high R-value. Installed by a professional, the price of spray foam varies depending on the thickness of the walls and type of foam. Spray foam insulation is probably the best overall insulation on the market if you can afford the cost. Foam insulation lowers your heating and your cooling loads when installed correctly. Additional benefits are elimination of air infiltration, keeps out dust, mold and allergens, and does not sag or deteriorate. Open cell foam is used more in residential applications. It is less expensive to install and is easier to work with after it's in place. Open cell allows water to penetrate, so it makes an excellent roof deck insulator. If water is allowed to penetrate, you can locate roof leaks before the decking deteriorates. Biggest benefit of open cell is heat transfer in sunny locations. It takes approximately 36 hours of sun to penetrate through 8 inches of foam. This is also true for walls. So when the home is cooled, it will stay cool. The warranty of the roof material is not voided with the installation of spray foam insulation. Closed cell foam has a much more structural component to it and can support some weight without compression. Closed cell does not allow water to penetrate and is an excellent insulator for basement and crawl walls where water could be a problem. Closed cell foam has a higher R-value per inch but is very ridged and tough to work with after installation. It is most often used in commercial applications. However, it has its useful applications in homes. Foam insulation keeps mold out of walls. Mold occurs in walls with batt insulation because of "thermal loop effect". This is where the heat penetrates the exterior wall, coming in contact with the cooler interior surface of the drywall, causing moisture to form. Moisture above 25% can provide an environment for mold to grow. Spray foam blocks this heat transfer and has no air gaps in which moisture can form. One way to combat the higher cost of spray foam is to combine a couple of inches of closed cell foam with fiberglass batt insulation installed over the foam, getting the exceptional air-blocking value of foam, with the high R-value and lower cost of fiberglass insulation. Spray foam insulation costs more than fiberglass batts, but it also has approximately twice the R-value of typical fiberglass batts insulation. By combining the two you will get the best of both. Foam insulation is also particularly good for remodeling projects when there is only easy access to the basement or crawl space and the attic. By blocking the air flow from the top (attic) and bottom (crawl or basement) you stop the draftiness that some older homes have, thus making the home more comfortable. A more comfortable home is what we all are looking to achieve. Spray foam can give you warmth in the winter and cooling in the summer when combined with the appropriate HVAC system. These systems can be smaller in size when your home is better insulated with less air infiltration.

 


Indianapolis

 

Southport Poly Foam Insulation

Southport The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as “Open Cell” because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the “open” space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across a spray foam insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam.

Indiana Spf Insulation

How to Paint Rope

Spray Insulation Under House Do you have a sneaking suspicion that the fiberglass insulation in your home or office is falling apart and not doing its job? Do you find bits of pink fluff everywhere? It might be time to ditch your tired old fiberglass insulation and replace it with something that will last. Spray foam is not only more resilient than other kinds of barriers, but it comes with numerous other benefits as well. If you're concerned about the condition of your home or building due to poor insulation, then spray foam can help solve your problems. Spray foam insulation is liquid polyurethane that dries into a tough foam consistency over a surface. Because it's liquid, it can fill in tiny cracks and holes that fiberglass can't protect. The thick, tightly sealed layer it creates is far more energy efficient than any other kind of material. It controls the indoor climate by keeping in more heat and cool air, depending on the weather. This will save you tons of money on electric bills, and be more comfortable for the occupants. Polyurethane insulation also doesn't come with any health risks. Fiberglass is made up of wiry, pink fibers that can make the skin sore and itchy if exposed to it. These fibers come loose and can be inhaled. Breathing in the fibers can cause lesions inside of the mouth and esophagus. Spray foam doesn't have tiny particles that break off and float into the air. It's also harmless to the touch, but is so durable that it does not crumble off anyways. Another benefit of spray polyurethane is that it can make your house or building more hygienic. The thick barrier prevents insects and other pests from sneaking inside. If you've had pest control problems in the past, spray foam insulation can be your new exterminator. Not even moisture stands a chance against its tough exterior. Spray foam keeps water out, which means it also keeps away dangerous mold, which can cost a fortune to repair. If you've been trying everything to get rid of mold, this material is excellent to use in existing homes. Since it can be a messy procedure, and previous insulation will have to be stripped and removed, it is recommended that only professional perform the service. You may be put off by the initial cost of having your home outfitted with a spray foam insulation kit. However, the money and time you will save in the future more than pays for itself. It will even add more value to the home or building, and you won't have to worry about replacing it. The best part about polyurethane is that it is environmentally friendly. If you're trying to make your house or building greener, then spray foam is the way to go. It is made from recyclable and renewable materials, and you'll be saving energy. Its versatility allows it to be sprayed almost anywhere, so you can even insulate the floors and ceilings. Spray foam insulation is a great move to make when you're improving your home or building.

How to Fix Holes in Tree Trunks

Spray In Foam Insulation R Value Polyurethane foam (PUR foam) had been widely used in most household and building installations. There are two types of polyurethane depending on how it is applied, the rigid form and the spray foam. Spray foam application is usually cheaper though less effective. Polyurethane foam is an insulation material with high thermal resistance because of the low-conductivity gas present. It is available in liquid formed but is applied using a spray equipment. HCFC or hydro chlorofluorocarbons are the usual gas used with an R-value range of R-7 to R-8 per inch. This R-value deteriorates in time through the process called thermal drift. As the low conductivity gas escapes through the air, gas molecules present in air replaces the gases in the insulation. This phenomenon usually starts after 2 years of installation. While the rigid board structure is more effective in insulating, application of spray polyurethane foam insulation relatively is easy since it molds to the form of the surface. Because of that it is also called, foamed-in-application. Most of the spray foam produce today has non-CFC (non-chlorofluorocarbon) gas as their foaming agent. While these non-CFC foams are less effective in insulation, they pose less threat to the ozone layer. It is also effective in a relative large range of temperature. An R-value of R-6 to R-6.5 per inch is normal for high density closed-cell PUR foam, about 32 kilograms per cubic meter (kg/m3). Low density open-cell PUR foam has about 8 kilogram per cubic meter (kg/m3). This has been noted to be more flexible than the regular polyurethane foams. Carbon dioxide as also been used as a forming agent for some low density foams. Spraying the polyurethane foam requires specific equipment and personnel using them must be properly trained. High density foams have usually slow-expanding capabilities. Low density foams expand rapidly when applied to walls' cavity sealing them almost instantly. However may cause over-expansion in the walls' surfaces creating damage. Using spray polyurethane foams in home insulation benefits the owner in many ways. Non-CFC foams are eco-friendly have no formaldehydes that may damage the ozone layer in the atmosphere. It can greatly eliminate air or wind infiltration the household. Air seeping through cracks or opening in the walls or roofing can increase convective air currents in attics or walls and also increase moisture and condensation rate inside the household. Since it is a very effective insulation, less energy can be used in terms of cooling and heating the household, while maintain the preferred comfort zone inside the house. It also passively strengthens the walls they are applied to. It has also long life span of more than 10 years which can be extended further by recoating. Installing or using spray polyurethane foam insulation, however must depend and customize to fit the home's building lay-out, cost of effectiveness, and even the climate wherein the home stands. While these considerations can be easily dealt with especially for someone with high budget, application of spray foam polyurethane, for best results must be left at the hands of experts.

How to Make a Spray Foam Tree

Best Spray Foam Insulation In A Can Now contemplate the recreational elements of the home, such as pools, spas, boats, recreational vehicles and trailers. Reducing the costs of heating your pool water by up to half will be easy if the underlying cavity and sides are insulated with polyurethane foam. Campers and trailers are rarely insulated beyond a cursory overlay, resulting in diminished use during the spring and autumn months. Why not extend your annual use of recreational vehicles by adding a layer of spray foam insulation? Plus, don't forget the spray foam will also help deaden noise from the road. Pleasure boats, dinghies, even yachts can benefit from polyurethane foam. Aside from the insulating qualities, there is added buoyancy. For small vessels like row boats and the kid's summer dinghy, that could be a great added safety benefit. In new construction and large renovations there is often a need to fill voids for adding to the structural integrity, sealing up air pockets, smoothing out uneven cavities and insulating HVAC components. Polyurethane foam is the perfect solution for all those needs. It gets into those little spaces and expands until there is nowhere else to go. Even buildings formerly used for storage can be spray foam insulated and converted to residential use. Or how about converting an old van or bus into a recreational vehicle? Insulate it with spray foam and you have a quiet, warm place to sleep while on that summer road trip. We know one of the qualities of polyurethane foam is the ability to repel moisture, and in turn prevent mildew and mold. In the event of a water problem such as a residential flood or hurricane damage, spray foam will provide a temporary dyke while a more concrete solution can be arranged. Now let's take that ability to resist liquid one step further, to hazardous materials. Polyurethane foam also resists oil and petrochemicals, which mean it can be used as a temporary hazmat spill containment solution.

 


Indiana