Wynndale Cellular Foam Insulation

Wynndale The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as “Open Cell” because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the “open” space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across a spray foam insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam.

Indiana Spf Insulation

How to Remove Expanding Foam

Blue Insulation Foam Now contemplate the recreational elements of the home, such as pools, spas, boats, recreational vehicles and trailers. Reducing the costs of heating your pool water by up to half will be easy if the underlying cavity and sides are insulated with polyurethane foam. Campers and trailers are rarely insulated beyond a cursory overlay, resulting in diminished use during the spring and autumn months. Why not extend your annual use of recreational vehicles by adding a layer of spray foam insulation? Plus, don't forget the spray foam will also help deaden noise from the road. Pleasure boats, dinghies, even yachts can benefit from polyurethane foam. Aside from the insulating qualities, there is added buoyancy. For small vessels like row boats and the kid's summer dinghy, that could be a great added safety benefit. In new construction and large renovations there is often a need to fill voids for adding to the structural integrity, sealing up air pockets, smoothing out uneven cavities and insulating HVAC components. Polyurethane foam is the perfect solution for all those needs. It gets into those little spaces and expands until there is nowhere else to go. Even buildings formerly used for storage can be spray foam insulated and converted to residential use. Or how about converting an old van or bus into a recreational vehicle? Insulate it with spray foam and you have a quiet, warm place to sleep while on that summer road trip. We know one of the qualities of polyurethane foam is the ability to repel moisture, and in turn prevent mildew and mold. In the event of a water problem such as a residential flood or hurricane damage, spray foam will provide a temporary dyke while a more concrete solution can be arranged. Now let's take that ability to resist liquid one step further, to hazardous materials. Polyurethane foam also resists oil and petrochemicals, which mean it can be used as a temporary hazmat spill containment solution.

How to Paint Rope

Pour Foam Insulation So, you have chosen to kick out the pink stuff and insulate your home using polyurethane foam insulation instead. Congratulations! You're on your way to reaping the benefits of more energy savings, less mold, fewer air leaks, greener materials, and twice the protective capability when compared to traditional fiberglass and cellulose insulation. But you won't see these advantages if you do not apply spray foam insulation properly - and that begins before you start spraying. Before you even think about moving forward, you should be thinking about safety. Protective safety goggles, full-cover clothing, a mask, and work gloves are a must for anyone applying expanding foam insulation. Make absolutely sure that no skin is exposed during application, because the adhesiveness of spray foam is similar to that of permanent glue: it will stick to skin and will not come off. If this occurs, the insulation will remain on your skin until your outer epidermal layer peels off. For the record, the only substances known to remove expanding foam are white spirit-based solvents - and only then if the insulation has not begun to set. Applying polyurethane foam insulation also opens the possibility of the material getting into your lungs, which can cause respiratory problems. In short, get confident in your ability to apply spray foam properly. Once you are ready to proceed, make sure the area where the spray foam is to be applied is between 65 and 80 degrees Fahrenheit. If it is not, either wait for the temperatures to decrease or warm the area using a bullet heater. Also, make sure the application area is clear of debris and dust in order to maximize adhesion. If there are holes or cracks in the walls or ceiling areas where you are spraying, make sure that you apply a sealant to insure a suitable air seal. Once the area to be sprayed is ready, you must turn your attention to the areas that will not be sprayed. Windows, doors, floors, drywall, and other areas must be masked with cloth or plastic sheeting so they won't be affected by over spraying. If there are any objects or structures that cannot be removed before spraying (such as air conditioners, plumbing piping, or heating units), then make sure they are completely covered as well. Again, one gap in your protective sheeting could result in a spot or stain which you may be unable to remove.

How to Remove Expanding Foam

Polyfoam Insulation Although spray foam insulation as we know it today truly emerged in the 1980s, spray foam actually has its roots several decades further in the past, beginning with the development of polyurethane foam in the 1940s by Otto Bayer. Otto Bayer, an industrial chemist, actually began working with polyurethane in Germany during the late 1930s. This technology was brought to the United States in the early 1940s by David Eynon, the president of Mobay, a war effort conglomerate created from the partnering of two chemical industry giants, Monsanto and the Bayer Corporation. Although Otto Bayer worked for Bayer Corporation, he was not related to the company's founding family. During the 1940s, polyurethane polymers were used primarily in military and aviation applications. The production of war machines for the World War II conflict drove most of the applications of these high-grade plastic polymers for the duration of the war. It was not until the 1950s that polyurethane began to be used in home insulation. It was the invention of the "Blendometer" that allowed for expansion of polyurethane application to the home insulation realm. The Blendometer was the first machine able to mix components for the creation of polyurethane foam and was created by Walter Baughman in 1953. The Blendometer allowed for the strategic mixing of chemicals to create what Baughman called a plastic elastomer or an expanding foam. Liquid when applied, this plastic elastomer expanded into a thick foam and eventually hardened upon drying. Baughman's Blendometer was still a partially manual process, with humans tilting trays of chemicals to mix foam. While the machine did allow for the use of polyurethane in home insulation as well as in other home-related applications, like air conditioner insulation, it was still a technology in its infancy and one that made widespread use of polyurethane as a residential insulation material no less cumbersome. Polyurethane polymers were used in a variety of means throughout the following decades, with incredible advancements being made in the auto industry applications of the material in particular. However, it would be more than two decades before the foam would become widely used in home insulation processes. Building on Baughman's invention, the first dedicated spray technology machine was constructed in 1963 by Fred Gusmer. The 1960s and 1970s saw technological advancements which made spray foam's use in home insulation more easily achievable and affordable. It was also in the 1970s that the idea of the "super insulated" home emerged. Largely driven by the energy crisis of the 1970s, home builders and homeowners alike began to look for ways to improve the energy efficiency of homes. The crisis fueled advancements in technology that laid the foundation for modern spray foam applications. It was the development of advanced spray nozzle technology that allowed spray foam insulation to be used widely in home construction and improvement projects. The spray foam nozzle allows the foam mixture and the chemical responsible for its expansion capabilities to be separated until just prior to application. The spray foam mixture consists of several key components but it is the expansion chemical, isosynate, which is responsible for its easy application and expansive character. The application nozzle allows the foam mixture and the isosynate to be delivered to the nozzle through separate hoses, mixing only seconds before being sprayed. The spray foam arrives at its destination as a liquid but quickly expands into a foam substance and later dries into a hardened plastic upon curing. The 1980s and early 1990s saw a great deal of controversy within the spray foam insulation industry as different marketing schemes from various companies promoted the benefits of closed verses open foam insulation and as some companies tried to market water blown foam application processes. Though there has been much debate within the industry, R-value standards, used as a measure of determining energy efficiency, have cleared up much of the controversy. R-value ratings clearly define closed foam as the most effective means of making a home as energy efficient as possible. Closed cell spray foam has additionally been added to the list of building requirements for making homes in hurricane and earthquake zones more structurally sound. The improved stability of homes insulated with spray foam technology makes the use of spray foam a smart move for any homeowner regardless of geographic location.

 


Indiana