Noblesville Closed Cell Spray Foam Insulation

Noblesville The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as “Open Cell” because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the “open” space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across a spray foam insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam.

Indiana Spf Insulation

How to Fix Holes in Tree Trunks

Cost Per Square Foot For Spray Foam Insulation Spray Foam Insulation is a two-component system typically consisting of petroleum oils, plastics, and resins. The polyurethane foam comes in two different forms, open cell and closed cell foam. The polyurethane spray foam is an extremely versatile material that is available in a variety of final physical properties and densities. Although the two types of foam are very similar in their chemical structures their characteristics and capabilities differ in many ways, which makes it necessary for the user to understand the differences of the two materials so he or she can determine which is the right foam for their particular application. The open cell spray foam insulation contains a density of 0.5lb. per cubic foot. The greater the density of the foam the heavier, or stronger it will become. This particular type of polyurethane foam is referred to as "Open Cell" because of the nature of the chemical reaction during the installation process. When the polyurethane foam is being applied the tiny cells of the foam are broken causing air to fill the "open" space inside the material, resulting in a soft or spongy material. The open cell foam carries an R-Value of 5 to 5.5 per inch (R-Value is the measure of thermal resistance, which can be found by identifying the ratio of the temperature difference across an insulator and the heat flux). 0.5lb. foam products use significantly less material than 2lb. foam products do when completing the same sized job, making them attractive to an individual concerned with conserving the foam material. Due to the fact that open cell foam requires less material, the cost of the project is much cheaper than it would be if you were to apply closed cell foam. Although, Open cell foam is an efficient and economical product it contains some disadvantages in regards to closed cell foam. One of the open cells disadvantages is it has a lower R-Valuer per square inch than closed cell foam does and open cell foam is vapor permeable requiring it to be covered with a vapor retardant material. Although, open cell foam has some advantages and disadvantages it has been recognized as an excellent insulator, air sealant and sound barrier. The second type of polyurethane foam is referred to as "closed-cell" or "2 lb foam". The closed cell foam gets its name from its individual chemical reaction. During the installation process the tiny cells that are created during the chemical reaction are not broken and are packed together. These little cells are filled with gas allowing the material to rise and become an excellent insulator. As mentioned earlier the higher the foams density the heavier, or stronger the foam will become. This type of foam carries a density strong enough to improve the structural integrity of the building it is applied to. Due to the higher density of this material it requires the use of more material resulting in a higher project cost. Some advantages of this foam includes its higher R-Value per square inch compared to open cell foam also, this foam is vapor resistant cutting out the additional cost of the vapor retardant material that open cell foam requires and it has the ability to improve the structural integrity of the building it is applied to. One major disadvantage is the products exceptionally high cost. The closed-cell foam commonly carries the highest R-value of any insulation material on the market at a value of 7.5 per inch. There are many things a home or building owner should take into consideration when considering the type of foam that should be used for their particular application. Although both types of foam are by far the best insulators on the market, each type of polyurethane foam possess its own characteristics and capabilities. It is imperative for the user to identify which foam is right for them before applying the product.

How to Remove Spray Foam Insulation

Blue Insulation Foam One of the most important keys to reducing your heating and cooling costs is having your home well-insulated. So what is the best insulation for your home? Spray Foam Foam insulation has two forms: Open and closed cell. Both are made from a polyurethane material and have different propellant agents added. Some are made from biodegradable materials, such as soybeans, to make the off-gases friendlier to the environment. Foam is probably the best insulation for blocking air infiltration combined with high R-value. Installed by a professional, the price of spray foam varies depending on the thickness of the walls and type of foam. Spray foam insulation is probably the best overall insulation on the market if you can afford the cost. Foam insulation lowers your heating and your cooling loads when installed correctly. Additional benefits are elimination of air infiltration, keeps out dust, mold and allergens, and does not sag or deteriorate. Open cell foam is used more in residential applications. It is less expensive to install and is easier to work with after it's in place. Open cell allows water to penetrate, so it makes an excellent roof deck insulator. If water is allowed to penetrate, you can locate roof leaks before the decking deteriorates. Biggest benefit of open cell is heat transfer in sunny locations. It takes approximately 36 hours of sun to penetrate through 8 inches of foam. This is also true for walls. So when the home is cooled, it will stay cool. The warranty of the roof material is not voided with the installation of spray foam insulation. Closed cell foam has a much more structural component to it and can support some weight without compression. Closed cell does not allow water to penetrate and is an excellent insulator for basement and crawl walls where water could be a problem. Closed cell foam has a higher R-value per inch but is very ridged and tough to work with after installation. It is most often used in commercial applications. However, it has its useful applications in homes. Foam insulation keeps mold out of walls. Mold occurs in walls with batt insulation because of "thermal loop effect". This is where the heat penetrates the exterior wall, coming in contact with the cooler interior surface of the drywall, causing moisture to form. Moisture above 25% can provide an environment for mold to grow. Spray foam blocks this heat transfer and has no air gaps in which moisture can form. One way to combat the higher cost of spray foam is to combine a couple of inches of closed cell foam with fiberglass batt insulation installed over the foam, getting the exceptional air-blocking value of foam, with the high R-value and lower cost of fiberglass insulation. Spray foam insulation costs more than fiberglass batts, but it also has approximately twice the R-value of typical fiberglass batts insulation. By combining the two you will get the best of both. Foam insulation is also particularly good for remodeling projects when there is only easy access to the basement or crawl space and the attic. By blocking the air flow from the top (attic) and bottom (crawl or basement) you stop the draftiness that some older homes have, thus making the home more comfortable. A more comfortable home is what we all are looking to achieve. Spray foam can give you warmth in the winter and cooling in the summer when combined with the appropriate HVAC system. These systems can be smaller in size when your home is better insulated with less air infiltration.

How to Remove Spray Foam Insulation

Polyurethane Foam One of the most important keys to reducing your heating and cooling costs is having your home well-insulated. So what is the best insulation for your home? Spray Foam Foam insulation has two forms: Open and closed cell. Both are made from a polyurethane material and have different propellant agents added. Some are made from biodegradable materials, such as soybeans, to make the off-gases friendlier to the environment. Foam is probably the best insulation for blocking air infiltration combined with high R-value. Installed by a professional, the price of spray foam varies depending on the thickness of the walls and type of foam. Spray foam insulation is probably the best overall insulation on the market if you can afford the cost. Foam insulation lowers your heating and your cooling loads when installed correctly. Additional benefits are elimination of air infiltration, keeps out dust, mold and allergens, and does not sag or deteriorate. Open cell foam is used more in residential applications. It is less expensive to install and is easier to work with after it's in place. Open cell allows water to penetrate, so it makes an excellent roof deck insulator. If water is allowed to penetrate, you can locate roof leaks before the decking deteriorates. Biggest benefit of open cell is heat transfer in sunny locations. It takes approximately 36 hours of sun to penetrate through 8 inches of foam. This is also true for walls. So when the home is cooled, it will stay cool. The warranty of the roof material is not voided with the installation of spray foam insulation. Closed cell foam has a much more structural component to it and can support some weight without compression. Closed cell does not allow water to penetrate and is an excellent insulator for basement and crawl walls where water could be a problem. Closed cell foam has a higher R-value per inch but is very ridged and tough to work with after installation. It is most often used in commercial applications. However, it has its useful applications in homes. Foam insulation keeps mold out of walls. Mold occurs in walls with batt insulation because of "thermal loop effect". This is where the heat penetrates the exterior wall, coming in contact with the cooler interior surface of the drywall, causing moisture to form. Moisture above 25% can provide an environment for mold to grow. Spray foam blocks this heat transfer and has no air gaps in which moisture can form. One way to combat the higher cost of spray foam is to combine a couple of inches of closed cell foam with fiberglass batt insulation installed over the foam, getting the exceptional air-blocking value of foam, with the high R-value and lower cost of fiberglass insulation. Spray foam insulation costs more than fiberglass batts, but it also has approximately twice the R-value of typical fiberglass batts insulation. By combining the two you will get the best of both. Foam insulation is also particularly good for remodeling projects when there is only easy access to the basement or crawl space and the attic. By blocking the air flow from the top (attic) and bottom (crawl or basement) you stop the draftiness that some older homes have, thus making the home more comfortable. A more comfortable home is what we all are looking to achieve. Spray foam can give you warmth in the winter and cooling in the summer when combined with the appropriate HVAC system. These systems can be smaller in size when your home is better insulated with less air infiltration.

 


Indiana